Flake Epoxy Flooring In Clyde North

Flake Epoxy Flooring Experts

Owner-operated epoxy floor specialists based in Clyde North, delivering seamless, hard-wearing coatings across Melbourne's South East.

GET A FREE QUOTE

Full Name *

Phone *

Short message about your needs *

I agree to terms & conditions provided by the company. By providing my phone number, I agree to receive text messages from the business.

0485 037 710

Armourstone Coatings

The flake system and the finishes you can choose

Flake epoxy flooring is a multi-layer system, not a single coat of paint. It starts with a tinted epoxy base coat, then coloured vinyl flakes (also called chips) are broadcast across the wet surface, and finally the whole floor is sealed under a clear polyaspartic or polyurethane topcoat that gives the surface its depth, gloss and toughness. The flakes come in different sizes and dozens of colour blends, so you can match a floor to a garage, a retail fit-out or an outdoor area. The biggest decision is coverage: a full-flake broadcast means flake is thrown to refusal until the base coat disappears completely, giving a rich, fully decorative, seamless finish; a partial-flake broadcast uses a lighter scatter so the base colour still shows through for a subtler, more budget-friendly look. You can also lean the blend light or dark to hide dust or tyre marks, and add anti-slip aggregate into the topcoat for wet areas like alfrescos and laundries. Whichever you pick, the result is a hard, seamless surface with no grout lines or joins for dirt to collect in.

Armourstone Coatings

How we prepare and lay a flake floor

Everything rests on preparation, and this is where a roll-on job fails. We start by diamond grinding the concrete to open the surface and create the right surface profile (CSP), so the coating keys into the slab instead of sitting on top of it. Before we coat, we check the slab for moisture using RH testing, because a damp slab will push a coating off no matter how good the product is. Any cracks, pop-outs and spalled edges are cut out and repaired, and a primer is applied so the base coat bonds evenly. Then the tinted base coat goes down and the vinyl flake is broadcast into it by hand while it is still wet - for a full-flake floor we throw to refusal so no base colour shows. Once cured, the loose flake is scraped and vacuumed back to a smooth surface, and two coats of clear polyaspartic or polyurethane topcoat are rolled on to build the mil thickness that carries the wear, UV stability and chemical resistance. The finished floor is seamless, easy to clean and ready to drive on once fully cured.

Armourstone Coatings

Why choose Armourstone for a flake floor

Daler Dhanoa runs Armourstone Coatings as an owner-operator, so the person who quotes your floor is the person grinding it, broadcasting the flake and rolling the topcoat - nothing is handed to a subcontractor. That matters most on a flake floor, because the finish is only as good as the prep underneath it and the evenness of the broadcast, and both come down to the hands doing the work. Based in Clyde North, we cover Casey and Cardinia and out to Warragul and Gippsland, so we are genuinely local rather than driving in from the other side of the city. We are open seven days a week, 7am to 9pm, which means we can grind and coat into the evening or across a weekend to fit around a working garage, a shop or a business that cannot lose floor space during trading hours. Every job is prep-first: diamond grind, moisture check, repair, then coat - never a quick roll-on that lifts within a year. You get a straight answer, a fixed price and a floor built to last. Call Daler on 0485 037 710 to talk through blends and coverage.

TESTIMONIALS

What Our Flake Epoxy Flooring Customers Say About Us

The Process

3 Step Process For Your Flake Epoxy Flooring Needs

Free Quote

Send us your floor size and photos, or we visit and measure. You get a clear, fixed quote up front with no surprises.

Surface Prep

We diamond-grind the slab, repair cracks and oil damage, then prime it. Proper preparation is what stops epoxy peeling or lifting later.

Final Coat

We lay the base, broadcast the flake, and seal with a tough topcoat. Your floor is ready to drive on within days.

areas we serve

Flake Epoxy Flooring

{{ custom_values.service_1 }} in {{custom_values.biz_area_1})

Clyde North

Armourstone Coatings is based right here in Clyde North, so this is the suburb we reach fastest and know best. Clyde North is one of Melbourne's fastest-growing corridors, with new estates like Meridian, Smiths Lane, Berwick Waters, Highgrove, Five Farms and Eliston handing over homes with bare, freshly poured double and triple-garage slabs every week. Those new slabs are exactly what epoxy is built for: they dust, stain and pick up hot-tyre marks the moment cars start using them, so coating them early protects the concrete long term. Owner Daler Dhanoa lives and works locally, diamond grinds every floor himself and never subcontracts, so Clyde North homeowners get an accountable local rather than a crew passing through. From garage flake finishes to driveway and path coatings, we cover the full range across every Clyde North estate. Call 0485 037 710 for a free fixed quote.

Beaconsfield

Beaconsfield blends established suburban streets with semi-rural blocks and acreage, and that mix shapes the epoxy work we do here. Many properties sit on larger parcels with big domestic sheds, detached workshops and multi-bay garages, so the floors are bigger and harder-working than a standard suburban garage. Sheds and workshops on these blocks cop machinery, hobby projects, oil and constant foot traffic, which is exactly where a ground-and-sealed epoxy floor earns its keep by staying sealed, dust-free and easy to sweep. Up in rural Beaconsfield Upper the sheds are bigger again. Armourstone Coatings, run by Clyde North owner-operator Daler Dhanoa, is a short drive away and diamond grinds every floor before any product goes down, whether it is a large shed slab or an upper-end home wanting a flake or metallic garage. Call 0485 037 710 for a free fixed quote.

Berwick

Berwick is unusual because it spans two very different housing types, and epoxy work here has to suit both. Around Berwick Village you find established brick homes with older garage slabs that carry years of wear, soaked-in oil staining and the occasional crack, while estates like Berwick Waters, Timbertop and Parkhill hand over fresh new-build slabs still waiting for their first coat. That mix means some Berwick floors need a repair-first approach while others simply need protecting early. Armourstone Coatings, run by Clyde North owner-operator Daler Dhanoa, handles both because every job starts with a proper assessment and a diamond grind rather than a one-size-fits-all coat. Whether your Berwick garage is decades old or freshly poured, we grind, repair where needed, then lay a hard-wearing flake or solid system. From garages and driveways to anti-slip and commercial floors, we cover the full range across Berwick. Call 0485 037 710 for a free fixed quote.

Cardinia

Cardinia is a rural shire locality of farms, large acreage blocks and hard-working sheds, so epoxy here is about function rather than a showroom garage. The typical Cardinia floor is a big machinery or implement-shed slab that lives with dust, mud, oil and heavy equipment day in, day out. Bare concrete on these blocks never stops generating dust and readily soaks up spills, which is why a ground-and-sealed or fully coated floor is such a practical upgrade. Armourstone Coatings, run by Clyde North owner-operator Daler Dhanoa, travels out to Cardinia's larger properties and coats these floors properly, diamond grinding first so the finish holds under machinery loads on rough, uneven slabs. From dust-controlling shed floors and grind-and-seal on big slabs to anti-slip coatings, we take on the practical rural jobs other coaters shy away from. Call 0485 037 710 for a free fixed quote.

Clyde

Clyde is the fast-growing new-estate neighbour right beside our Clyde North base, so it is one of the suburbs we reach quickest and know intimately. Like its neighbour, Clyde is filling with brand-new homes handing over bare double-garage slabs, but here we also see strong demand for alfresco flake finishes as families set up their outdoor entertaining areas. New slabs dust and pick up tyre marks quickly once cars move in, while alfresco concrete needs a UV-stable, non-slip finish that looks the part and shrugs off weather. Owner-operator Daler Dhanoa coats both properly, diamond grinding first and matching flake blends across your home. Being next door means fast response and easy follow-up if you want the garage now and the alfresco later. From garages and driveways to decorative flake and anti-slip, we cover Clyde in full. Call 0485 037 710 for a free fixed quote.

Cranbourne

Cranbourne is a large, well-established suburb where most garage slabs have years of use behind them, and that makes resurfacing and repair the heart of the work here. Unlike the new-estate corridors nearby, Cranbourne floors are typically older, often oil-stained, worn or cracked, and sometimes attached to light-commercial premises along the High Street strip as well as homes. Those tired slabs are exactly where a proper diamond grind, repair and recoat transforms a floor that looks past its best into a clean, sealed, hard-wearing surface. Armourstone Coatings, run by Clyde North owner-operator Daler Dhanoa, is a short drive from Cranbourne and specialises in reading an aged slab correctly before coating it, never rolling product over contamination. From resurfacing oil-stained garages and repairing cracks to light-commercial floors and anti-slip coatings, we cover the practical jobs Cranbourne's established homes and businesses need. Call 0485 037 710 for a free fixed quote.

Cranbourne West

Cranbourne West is a genuine two-sided suburb, and epoxy demand splits neatly down the middle. On one side sits the Cranbourne West industrial precinct off Thompsons Road and Evans Road, packed with warehouses, workshops and factory units where bare concrete cracks, dusts and stains under forklift and foot traffic. On the other are the newer residential estates around Sandhurst and Ranfurlie, where families want garage floors that stop lifting dust and shrug off hot tyres. Armourstone Coatings covers both from our Clyde North base, a short run down the freeway. We diamond grind every slab first, whether it is a 400 square metre warehouse floor or a single garage, then build the system up in layers so it holds under the load it will actually see. One local contact, no subcontractors, prep done properly.

Polyaspartic Floor Coating in Clyde North

Nar Nar Goon

Nar Nar Goon is a small rural township on the eastern edge of the Cardinia shire, and the floors here are nothing like a suburban garage. It is farms, hobby blocks and acreage, which means machinery sheds, implement sheds and hobby-farm workshops where the concrete copes with tractors, utes, dropped tools and everything a working property throws at it. Bare rural slabs shed a fine dust that gets into every tool and bench, while diesel, oil and fertiliser soak straight in and stain. Armourstone Coatings travels out to Nar Nar Goon from Clyde North to grind and coat these floors properly, whether it is a big machinery-shed slab wanting a tough grind-and-seal, a hobby-farm workshop after a full flake system, or the house garage on the block. We size the coating to the load the slab carries, and we do the prep that makes it last on a working property.

Polyurethane Floor Coating in Clyde North

Narre Warren

Narre Warren is one of the largest established suburbs in Melbourne's south east, anchored by the Fountain Gate retail and commercial hub off the Princes Highway, Overland Drive and Victor Crescent. That gives it a distinctive two-sided epoxy market. On one side sit the shops, showrooms, cafes, gyms and medical fit-outs around the Fountain Gate precinct, all needing floors that look sharp under lighting and stay safe underfoot. On the other sit thousands of established brick homes whose garage slabs have been dusting and staining for decades. Armourstone Coatings covers Narre Warren from nearby Clyde North, so response is quick either way. For the commercial side we lay hard-wearing, anti-slip floors that keep a business trading. For established garages we grind back the tired, oil-stained slab and finish with a flake system that makes a decades-old garage look new. Call 0485 037 710 for a free fixed quote.

Officer South

Officer South is one of the fastest-filling pockets of the Cardinia growth corridor, and it is largely a first-home and new-build suburb. Estates like Kaduna Park, Arena, Timbertop and the Bridgewood precinct are handing over house-and-land packages week after week, and nearly every one arrives with a bare double or triple garage slab and a fresh alfresco pad out the back. New concrete looks clean, but left uncoated it dusts, marks and lifts under hot tyres inside a season, and a green slab still holding moisture will blister a rushed coating. Armourstone Coatings covers Officer South from nearby Clyde North, a quick run up the corridor, and specialises in catching these floors early with a flake finish and a tough polyaspartic topcoat. Owner-operated by Daler Dhanoa, diamond-ground first, quoted up front. Call 0485 037 710 for a free quote.

Pakenham

Pakenham is the biggest centre at the eastern end of our core coverage, and it packs three epoxy markets into one town. First there is the Pakenham industrial and business park around Bald Hill Road and the Racecourse Road precinct, full of warehouses, factories and workshops where the floor is a working asset that carries forklifts, spills and traffic all day. Then there are the fast-growing estates on the Lakeside, Cardinia Lakes, Arena and Heritage Springs side, handing over bare garage slabs by the week. And there is a large stock of established homes off Main Street with older slabs due for resurfacing. Armourstone Coatings covers all three from Clyde North, and Pakenham marks the furthest-east point of our core area before Gippsland. We diamond grind every floor first, then build the right system: a high-build, anti-slip industrial floor for a factory, or a flake garage finish for a home.

Warragul

Warragul is a Gippsland regional town about 40 minutes east of our Clyde North base, and the clearest sign that Armourstone genuinely travels for the right job. It is a mixed market: established homes with older garage slabs, a growing commercial and main-street base around Queen Street and Smith Street, and surrounding rural properties with big machinery sheds and workshops. Locals often rely on the same handful of Gippsland operators, so a prep-first installer who actually drives out is worth having. Armourstone covers Warragul as part of our regional Gippsland reach, and the method does not change for the distance: we diamond grind every slab first, then build the right system, whether that is a flake garage floor, a grind-and-seal for a large rural shed, or a hard-wearing commercial floor. Owner-operated by Daler Dhanoa, nothing subcontracted, and quoted up front so travel never becomes a surprise on the invoice.

Flake Epoxy Flooring In Clyde North

FREQUENTLY ASKED QUESTIONS

Everything you need to know about our Flake Epoxy Flooring In Clyde North

How much does flake epoxy flooring cost?

Flake epoxy flooring generally runs from about $65 to $120 per square metre, with a single garage from roughly $1,000 to $2,000 and a double from around $2,000 to $3,500. The final price depends on the size of the area, the condition of the slab, whether you want full-flake or partial-flake coverage and any extras like coving or anti-slip aggregate. A clean new slab is cheaper to prepare than one with oil stains, cracks or moisture. We never quote a flat rate blind, so Armourstone comes out, checks the concrete and gives you a free fixed quote. Call 0485 037 710 to arrange it.

How long does it take and when can I drive on it?

Most single and double garages are done in two to three days, because flake is a layered system that needs the base coat to cure before we scrape back and topcoat. You can usually walk on the floor the day after the final topcoat and put light foot traffic on it soon after. Driving on it takes longer - as a rule, allow around five to seven days before parking a car so the topcoat reaches full cure and avoids hot-tyre pickup. We give you exact timings for your floor when we quote. Rushing the drive-on time is the fastest way to mark a fresh coating.

Will a flake floor peel or lift over time?

Not when the slab is prepared properly, which is the whole point of how we work. Peeling and lifting almost always trace back to poor prep - a floor rolled over a smooth or damp slab with no grinding. Armourstone diamond grinds every floor to create the right surface profile, runs a moisture check before coating and repairs cracks and spalling first, so the flake system bonds into the concrete rather than sitting on top of it. The clear polyaspartic topcoat then adds UV stability and abrasion resistance so the finish holds up to traffic and cleaning. Because Daler does the prep himself on every job, nothing gets skipped.

What does the process involve from start to finish?

First we come out, measure the floor, check the slab and give you a free fixed quote, and you choose your flake blend and coverage. On the job, we diamond grind the concrete, test for moisture, then cut out and repair any cracks, pop-outs or spalled edges. Next we prime, roll the tinted base coat and broadcast the vinyl flake into it by hand while it is wet. Once cured, we scrape and vacuum back the loose flake and apply two clear polyaspartic or polyurethane topcoats to build the finish. You are left with a seamless floor and clear timings for walk-on and drive-on.